Видео

At 2:00 the video is wrong. The output of the circuit is tied to ground. So there will not be a signal to measure at 2:14. What happens is this: When capacity increases (more moisture), the voltage swing across the capacitor will decrease. Vice versa, when capacity decreases (less moisture), the swing will increase.

do you have a website?

Thank You so much @BasonTech for the debounce code and the wonderful explanation.

Can you help me to build a circuit for my University project?

Which software you use to write code

You explained it great, but I did the same thing you did and the code just does not work.

I watched a bunch of tutorials on this topic, and this is by far the most helpful.

Can i use this glcd with esp32 wroom??

Explain this 0 is high and 1 is low?

Thankyou. Very clear. I started playing with arduinos again and had totally forgotten how to do the 7 segment x 8.

Super clear Sketch!! thank you for your service 🙂

clear and simple thanks

Thank you for the nice explanations. Is there any ways which I can be able to save the plotted audio into WAV or MP4 to an SD Card or by using PySerial?

Great video Bas :) i bumped into your channel and I immediately got hooked on the quality of your explanation! I did follow the tutorial with ease. Unfortunately my rotary encoder is still giving me false values (even when I try to move it slowly). I am thinking to apply some filter on the raw values (avg of 3) perhaps? Any pro advice on how manufacturers usually solve problems like that?

Your video tutorial helps me a lot on setting up my soil sensor. However i cant use it yet since i dont have the code, where can i see the code? if it's okay, for my research

Remember, this sensor cant measure noise level (dB). The amplitude on diagrams dont show noise level, it only shows how long sound sensor was triggered on. When it is quieter, the sensor does not detect the quieter sound as a lower noise level, but activates fewer times in a set period of time.

hi...please can pro mini be used with TB6612fgn to drive DC or stepper motor...thanks

Is the pro mini capable of working with a mpu9250?

Thanks you so much! But, I have a question can this sensor measure the negative voltage?

How to utilize these value for perdition as i want send to ai model value which i build for perdition , as want to perdidict baby is crying or not?? Please anyone can help

What is that gold circle for? Anyone know?

Also, I'm not sure which, if any, of these three have this capability, but when I built a MIDI controller for my computer, I went with the Leonardo because it can be set to be recognised as a standalone USB device when plugged in.

It's possible to stream the sound directly with the PC speakers??

hey Bas, I am using a type of remote same as you do but each and every button i press near the IR receiver I only get codes like FFFFFFFFF FFFFFFFFF FFFFFFFFF FFFFFFFFF FFFFFFFFF FFFFFFFFF But when i take to a certain distance i get many different codes like for each button i get many code more than 20 or 30 i dont know which one to choose can you help me with this out.🤥🤥🤥🤥

hello, can I use the capacitive soil moisture sensor to detect/measure moisture in oil

Hi, I am 12 years old. What is the use for the project ? 10Q

how can i take in output two numbers instead of only one??

Does the display come with the pins pre-soldered on it?

Thank you, you are a lifesaver!

Heyy! How could I read direct digits like if 1000-1022 for example. If you could please provide code you will be AMAZING!

Can you share tge code

I NEVER SAW you connect the 12vdc on your video I m trying to calculate this 5000vdc and the R1 is equal to 5meg ohms, what is the required R2?

$5 ty!

#3TY!

TY #2!

TY!

input pin! not out pin!

By you accent I am sure that you are Dutch.😊

How can I calibrate LDR?

Can you please make a tutorial on using a capacitive soil moisture sensor , Arduino Uno to make a automatic watering system? I have tried but I can't trigger the motor! tried a mos module and a relay same result :(

Amazing! Can you show us if there is a way in which we can convert this analog read into dB? really useful if you could. thanks in advance

Thank you❤ That's very useful for me🌹🥰

Good video. Though the idea of shields is not unique. Intel used it on their boards 40 years ago. I used them and later made designs with piggyback cards on top of my main boards.

Hi, not sure why, i have included the simple code in IDE, yet when i compile it it gives me error codes This is the code, which i think is identical to yours. What am I missing? void setup() { // put your setup code here, to run once: pinMode(5, INPUT); pinMode(LED_BUILTIN, OUTPUT); digitalWrite(LED_BUILTIN; LOW); } void loop() { if(digitalRead(5) == HIGH) { digitalWrite(LED_BUILTIN, HIGH); } else { digitalWrite(LED_BUILTIN, LOW); } delay (100); }

My thing only outputting 1

hi i tried it in spi mode but seems like my lcd is not working it just remains completely blank i checked the connections and the code both of them are fine ?

"In this tutorial im going to show how to use the sound sensor on a serial plotter" **MM2 Roblox music starts playing**

Awesome! Whats the smallest size this servo can get?

Can you list the components used

can we use the same pin if we have multiple led traffic light?